INSTRUCTIONS FOR
LOW VOLTAGE DIMMING KITS
ALL KITS COME PRE-LINKED, ONLY DO THIS TO ADD OR REMOVE SWITCHES OR CONTROLLERS
For basic linking, an Express Link Mode is accessible for 5 minutes after power up.
Link Modes 1 - 4 are accessible anytime for basic or advanced configuration:
Express Link Mode - can be used to link switches in Rocker Mode. The power LED blinks 1x per second while the Express Link Mode is active.
1. During the first five minutes after power up, wireless switches may be linked by clicking the ON button three times, then the OFF button three times and then the ON button 3 times. The ON is the Top button, indicated on the switch front with an up arrow or on the back with the letter “I”.
2. The Dimmer confirms when a switch is linked by blinking the light and dimming up. Un-link is confirmed by blinking the light and dimming down.
EXPRESS MODE | TRIPLE PRESS | CONFIRM-ATION |
Link | ON-OFF-ON | Blink, Dim Up |
Un Link | OFF-ON-OFF | Blink, Dim Down |
RANGE: | 50-150 FT (typical) |
FREQUENCY: | 902 MHz |
POWER INPUT: | 8-30 VDC |
POWER OUTPUT: | 5A, 100W Class II Low Voltage |
MAX LOADS / CONTACT RATINGS: | RESISTIVE LOAD 10A TUNGSTEN 1000W FLUORESCENT 600W LED LAMP 200W |
MEMORY: | LINK UP TO 10 SWITCHES |
OPERATING TEMP: | -32° - 140° F (° - 60° C) |
DIMENSIONS: | 2.88x1.3x0.67 IN (73x33x17mm) |
RADIO CERTIFICATION: | FCC: SZV-TCM300U I.C. 5713A-TCM300U |
1. Short press the CLR button to maually control Dimmer and verify power connections.
2. Power LED meaning:
POWER LED PATTERN | MEANING |
OFF with no flicker on | No Power |
ON with flicker off 1x per second | Express Link Mode is active. Powered up for less than 5 min. |
ON with no flicker off | Basic Link Mode is inactive. Powered up for more than 5 min. |
Flicker when switch or sensor transmits | Compatible signal received that is not linked |
Double flicker when switch or sensor transmits | Compatible signal received that is linked |
Steady ON/OFF blink ~1x per second | Link Mode is active |
Repeating blink pattern with pause | Indicate which Link Mode is active |
OFF & flickers ON every 3 seconds | Output power shorted. Disconnect output and clear the short |
CLR BUTTON
Test: Short press CLR button to cycle between 0%, Preferred Level and 100%. Long press CLR button to manually dim up and down, subsequent long presses reverse dim direction.
Delete All Links: Hold the LNK button to activate Link Mode 1. Dimmer is blinking. Hold the CLR button (7s). After 7 seconds blinking pauses while the links are deleted and resumes blinking when the delete process is complete. Release CLR. Link Mode 1 is active when the button is released.
Restore Factory Defaults: Hold the LNK button to activate Link Mode 1. Hold the CLR button for 20 seconds to restore factory defaults. Blinking will pause at 7 seconds to delete links, then resume, keep holding. After 20 seconds, blinking will stop and factory defaults are restored. Release button.
REPEATER
With the repeater active, the Dimmer will respond to linked controls and will also extend the wireless range by forwarding signals for all controls in the area, whether they are linked to the Dimmer or not. Activate 2 or more repeaters to extend the range up to 2 hops. Signals repeated twice will not be repeated again.
Change repeater status by holding the LNK button while applying power to the Dimmer. The Power LED will blink the new repeater status: 1 - Disabled, 2 - Enabled. It is recommended that not more than 10 repeaters be activated in the same area to reduce the possibility of interference from too many repeaters.
OUTPUT MODE
Change output mode by holding the CLR button while applying power to the Dimmer. The Power LED will blink the new mode status:
1 = Dimming: Adjustable brightness
2 = Switching: ON/OFF switching mode, no dimming
STATE MEMORY
The Dimmer powers up to the same state that was active prior to power loss whenever a switch is linked to the Dimmer. Upon initial installation the receivers will power up ON when they are not linked to any devices or if only a motion sensor is linked.