INSTRUCTIONS FOR
5A ON/OFF RECEIVERPart # RW9-5C
Installing at Fixture Location:
Installing at the Switch Location:
2. On the receiver, find the linking button.
5. End the linking sequence by either waiting 30 seconds or completing a power cycle. Once the blinking stops, the receiver has exited linking mode and you can now use your switch normally.
SWITCH LOCATION INSTALL
FIXTURE LOCATION INSTALL
|
RANGE:
|
50-150 FT (typical)
|
|
FREQUENCY:
|
902 MHz
|
|
POWER SUPPLY INPUT RATING:
|
100-277 VAC 50/60 Hz
|
|
RELAY OUTPUT:
|
Single, non-isolated latching SPST relay. 1) Electronic or LED Driver Loads: 5 Amps resistive at 100-277 VAC. 2) Motor Loads: 1/4 HP |
|
MAX LOADS / CONTACT RATINGS:
|
5A (All loads: LED, Fluorescent, 1/4 HP motor, etc) 70A Max Inrush Current |
|
MEMORY:
|
Link up to 25 wireless switches
|
|
TEMPERATURE SPECS:
|
Operating Temp: 32° to +122°F (0° to +50°C)
Storage Temp: -4° to +176°F (-20° to +80°C) Humidity: 10-95% non-condensing |
|
DIMENSIONS:
|
1.73(W) x 2.61(H) x 1.09(L) inches (66x44x28mm)
|
|
CERTIFICATIONS:
|
ETL: UL 60730 (U.S.)
ETL: CSAc22.2#14-05 (Canada) CE: IEC 60730 ETL: UL 2043 (Plenum) IEC61000-4-5 (Surge) FCC: SZV-STM300U (United States) IC: 5713A-STM300U (Canada) |
Press and release the SELECT button to toggle receiver (controller) ON and OFF.
After linking, press the Link button on a sensor 6 times to activate the Link Test Mode. Subsequent presses from any linked sensor will cause the relay to toggle confirming the sensor is linked and testing the reliability
of wireless communications. Link Test Mode will time out after 60 seconds of no activity.
1. Activate Simple Link Mode by holding the MENU button until the controller starts toggling.
2. Hold the SELECT button for 10 seconds to Clear All Links from the controller.
To remove one Link from controller and leave others unaffected:
1. HOLD the MENU button to activate Link Mode. The toggling output confirms Link Mode is active.
2. TRANSMIT the Link Signal by triple pressing the top button on switches or single pressing the Link (or teach) button on sensors. Controller pauses in OFF position for 3 seconds when the link is deleted, then toggling resumes.
3. WAIT 30 seconds for Link Mode to exit automatically (toggling stops).
Repeater function is DISABLED by default and may be enabled on specific controllers to extend the range by
retransmitting all packets 1 or 2 times. Repeater mode may be changed using Advanced Setup instructions.
Transmit - -> Repeater 1x - -> Repeater 2x - -> Receive
ADVANCED SETUP:
Advanced Setup uses the Status LED to navigate a hierarchy of menus with blink patterns in one of 3 colors: Amber, Green, and Red. The relay output does not toggle while using Advanced Setup. Navigation overview:
1. Hold MENU button 15 seconds until Status LED blinks Amber pattern.
2. Press SELECT button to cycle through blink count options.
3. Press MENU button to enter/save menu item.
4. Hold MENU for 5 seconds to exit menu option.
1 - ACTIVATE ADVANCED SETUP
A. Hold MENU button 15 seconds until Status LED blinks Amber pattern.
B. Jump to 2 - Link Mode or 3 - Setup.
2 - LINK MODE: AMBER MENU BLINKS 1-5
A. Press SELECT button to cycle blink count and choose a Link Mode. Different devices may be linked in different modes.
B. Transmit Link Signal with fast triple press of switch button or single press of Link button on sensors. Status LED will pause Green when link is added. If Link Signal is transmitted a second time, Status LED will pause Red indicating link is removed.
C. Optional - Press MENU button to see Green blinks indicating number of devices linked in the active mode. Red blink means no devices linked. Hold MENU button 5 seconds to return to Amber Menu.
D. Wait 60 seconds or hold MENU button for 5 seconds to return to Operating Mode.
3 - SETUP: AMBER MENU BLINKS 6-7
A. Press SELECT button to cycle to Config (6 Amber blinks) options.
B. Press MENU button to activate Green Menu.
C. Press SELECT button to cycle through Green blink options.
D. Press MENU button to activate Red Menu.
E. Press SELECT button to cycle through Red blink options or hold SELECT button to adjust level if applicable.
F. Press MENU button to save selection.
G. Hold MENU button for 5 seconds to return to Green Menu.
H. Hold MENU button for 5 seconds to return to Amber Menu.
I. Hold MENU button for 5 second
