INSTRUCTIONS FOR

ON/OFF SWITCH KITS


Please check the Part Number on your Receiver and follow the corresponding instructions for troubleshooting:

RW9-5C

  • 2. unscrew fixture to access wires - showing wiring diagram of neutral wires, power in and out, ground wires
  • 3. connect receiver wires to fixture wires - wiring diagram of 5 amp receiver connected to fixture wires with neutral, black, white, blue, power in and out, and ground wires
ALL KITS COME PRE-LINKED, ONLY DO THIS TO ADD OR REMOVE SWITCHES OR CONTROLLERS
1. Confirm the receiver has power and the status LED shows and responds to the receiver's output: green = on and red = off.

2. On the receiver, find the linking button.

3. Press and hold the linking button for about 5 seconds. The receiver and light fixture will start toggling between on and off at regular intervals.
4. Click the top of the switch 3 times. The status LED will either pause: green = switch added OR red = switch removed.

5. End the linking sequence by either waiting 30 seconds or completing a power cycle. Once the blinking stops, the receiver has exited linking mode and you can now use your switch normally.

SWITCH LOCATION INSTALL

FIXTURE LOCATION INSTALL

RANGE:
50-150 FT (typical)
FREQUENCY:
902 MHz
POWER SUPPLY:
SELF-GENERATED WHEN SWITCH IS PRESSED
OUTPUT CHANNELS:
LINK TO ANY NUMBER OF RECEIVERS IN RANGE
DIMENSIONS:
2.75(W) x 4.5(H) x 0.62(D) inches
RADIO CERTIFICATION:
FCC (UNITED STATES)
ADDRESSING:
FACTORY SET UNIQUE ID (1 OF 4 BILLION)
RANGE:
50-150 FT (typical)
FREQUENCY:
902 MHz
POWER SUPPLY INPUT RATING:
100-277 VAC 50/60 Hz
OUTPUTS:
1 - 5A Latching Form A Relay
MAX LOADS / CONTACT RATINGS:
RESISTIVE LOAD 10A

TUNGSTEN 1000W

FLUORESCENT 600W

LED LAMP 200W

MEMORY:
LINK UP TO 10 SWITCHES
OPERATING TEMP:
-32° to 122° F (0° to 50° C)
DIMENSIONS:
1.1(L) x 1.6(W) X 3.3(H) inches
CERTIFICATIONS:
ETL: UL 60730 (U.S.)
ETL: CSAc22.2#14-05 (Canada)
CE: IEC 60730
ETL: UL 2043 (Plenum)
IEC61000-4-5 (Surge)
FCC: SZV-STM300U (United States)
IC: 5713A-STM300U (Canada)
TEST FUNCTION:
Press and release the SELECT button to toggle receiver (controller) ON and OFF.


SENSOR LINK TEST MODE:
After linking, press the Link button on a sensor 6 times to activate the Link Test Mode. Subsequent presses from any linked sensor will cause the relay to toggle confirming the sensor is linked and testing the reliability
of wireless communications. Link Test Mode will time out after 60 seconds of no activity.


CLEAR ALL LINKS:
1. Activate Simple Link Mode by holding the MENU button until the controller starts toggling.
2. Hold the SELECT button for 10 seconds to Clear All Links from the controller.


SELECTIVE LINK DELETION:
To remove one Link from controller and leave others unaffected:
1. HOLD the MENU button to activate Link Mode. The toggling output confirms Link Mode is active.
2. TRANSMIT the Link Signal by triple pressing the top button on switches or single pressing the Link (or teach) button on sensors. Controller pauses in OFF position for 3 seconds when the link is deleted, then toggling resumes.
3. WAIT 30 seconds for Link Mode to exit automatically (toggling stops).


REPEATER MODE:
Repeater function is DISABLED by default and may be enabled on specific controllers to extend the range by
retransmitting all packets 1 or 2 times. Repeater mode may be changed using Advanced Setup instructions.
Transmit - -> Repeater 1x - -> Repeater 2x - -> Receive 


ADVANCED SETUP
Advanced Setup uses the Status LED to navigate a hierarchy of menus with blink patterns in one of 3 colors: Amber, Green, and Red. The relay output does not toggle while using Advanced Setup. Navigation overview:
     1. Hold MENU button 15 seconds until Status LED blinks Amber pattern.
     2. Press SELECT button to cycle through blink count options.
     3. Press MENU button to enter/save menu item.
     4. Hold MENU for 5 seconds to exit menu option.


1 - ACTIVATE ADVANCED SETUP
     A. Hold MENU button 15 seconds until Status LED blinks Amber pattern.
     B. Jump to 2 - Link Mode or 3 - Setup.


2 - LINK MODE: AMBER MENU BLINKS 1-5
     A. Press SELECT button to cycle blink count and choose a Link Mode. Different devices may be linked in       different modes.
     B. Transmit Link Signal with fast triple press of switch button or single press of Link button on sensors.   Status LED will pause Green when link is added. If Link Signal is transmitted a second time, Status LED will   pause Red indicating link is removed.
     C. Optional - Press MENU button to see Green blinks indicating number of devices linked in the active   mode. Red blink means no devices linked. Hold MENU button 5 seconds to return to Amber Menu.
     D. Wait 60 seconds or hold MENU button for 5 seconds to return to Operating Mode.


3 - SETUP: AMBER MENU BLINKS 6-7
     A. Press SELECT button to cycle to Config (6 Amber blinks) options.
     B. Press MENU button to activate Green Menu.
     C. Press SELECT button to cycle through Green blink options.
     D. Press MENU button to activate Red Menu.
     E. Press SELECT button to cycle through Red blink options or hold SELECT button to adjust level if   applicable.
     F. Press MENU button to save selection.
     G. Hold MENU button for 5 seconds to return to Green Menu.
     H. Hold MENU button for 5 seconds to return to Amber Menu.
     I. Hold MENU button for 5 second

RW9-5C-B

  • 2. unscrew fixture to access wires - showing wiring diagram of neutral wires, power in and out, ground wires
  • 3. connect receiver wires to fixture wires - wiring diagram of 5 amp receiver connected to fixture wires with neutral, black, white, blue, power in and out, and ground wires
ALL KITS COME PRE-LINKED, ONLY DO THIS TO ADD OR REMOVE SWITCHES OR CONTROLLERS
1. Press button on receiver for 3 seconds until the receiver begins to toggle on/off.
2. Press the TOP of the switch 3 times quickly to link the switch to the receiver, or the BOTTOM of the switch 3 times to unlink.
3. The LED and output will pause ON for 3 seconds if linked, or OFF for 3 seconds if unlinked.
4. Wait for the linking mode to time out (30 seconds), or power cycle the receiver.
5. Test switch to ensure it's linked properly.

SWITCH LOCATION INSTALL

FIXTURE LOCATION INSTALL

RANGE:
50-150 FT (typical)
FREQUENCY:
902 MHz
POWER SUPPLY INPUT RATING:
100-240 VAC 50/60 Hz
RELAY OUTPUT:
1 FORM A RELAY 10A
MAX LOADS / CONTACT RATINGS:
RESISTIVE LOAD 10A

TUNGSTEN 1000W

FLUORESCENT 600W

LED LAMP 200W

MEMORY:
LINK UP TO 10 SWITCHES
OPERATING TEMP:
-40° - 104° F (-40° - 60° C)
DIMENSIONS:
1.1(L) x 1.6(W) X 3.3(H) inches
RADIO CERTIFICATION:
FCC (UNITED STATES)
RANGE:
50-150 FT (typical)
FREQUENCY:
902 MHz
POWER SUPPLY:
SELF-GENERATED WHEN SWITCH IS PRESSED
OUTPUT CHANNELS:
LINK TO ANY NUMBER OF RECEIVERS IN RANGE
DIMENSIONS:
2.75(W) x 4.5(H) x 0.62(D) inches
RADIO CERTIFICATION:
FCC (UNITED STATES)
ADDRESSING:
FACTORY SET UNIQUE ID (1 OF 4 BILLION)
CONFIRM RECEIVER IS WIRED CORRECTLY & IS FUNCTIONAL:
Test the status light on the receiver by pressing the CTRL button. Green means the output should be ON, Red means the output should be OFF. If the status light is not working, that indicates the power is not ON, wiring is incorrect, or receiver has been damaged. If the status light turns ON, but the light doesn’t turn ON, the wiring could be incorrect or it could be a bulb failure.

CONFIRM SWITCH IS FUNCTIONAL:

Press the top of the switch to turn the receiver ON and the bottom of the switch to turn it OFF. If the receiver doesn’t respond, the switch may not be linked.